A constant leaking faucet won't only drive you crazy, but it will also add up your water bill significantly. However, you don't need to freak out if you have a leaking Delta kitchen faucet. You can actually fix it quite easily on your own, provided that you have the right tools and materials.
If you have a Delta kitchen faucet that's been leaking, there are some easy steps you can take to fix it without having to call a professional or replace the entire faucet. Read on to learn how to fix your Delta handle kitchen faucet.
Tools and Materials Needed:
- Adjustable pliers
- Allen wrench
- Flat head screwdriver
- Rubber gloves
- Delta replacement cartridge (can be found online or at a hardware store)
- White vinegar
- Replacement springs and gaskets
Instructions on How to Repair a Leaky Delta Kitchen Faucet
Shut Off the Water Supply
Before you do anything, you'll need to shut off the water supply to your Delta kitchen faucet. Locate the shut-off valves beneath the sink and turn them clockwise to close them.
Remove the Faucet Handle
Once the water is shut off, you can remove the handle. Use an Allen wrench to remove the set screw that holds the handle in place. Once the set screw is removed, you should be able to pull the handle off. Lift the handle up straight to remove it from the faucet stem.
Remove the Bonnet or Hex Nut
With the handle removed, you should be able to see a bonnet or hex nut. Use an adjustable wrench to remove this piece. If the bonnet is stuck, you may need to use a pair of pliers to get it started.
Remove the Collar
Under the bonnet, you will find a collar. This piece is threaded and can be removed by hand. Put on a rubber glove to increase traction, grip the collar on the top of the faucet body and turn it counterclockwise. You may need to channel lock pliers to keep things moving.
Remove the Stem
Once the collar is removed, you should be able to pull the stem out of the faucet. If it is stuck, you may need to use a pair of pliers. Remove the stem by pulling it straight up and out of its housing. Use pliers, if necessary, gripping the spindle at the top of the stem.
Remove the Ball, Gaskets, and Springs
The next step is to remove the ball, gaskets, and springs. The ball is located under the stem and is held in place by a screw-on cap. Unscrew the cap with a Phillips head screwdriver and pull out the ball. Remove the gaskets and springs from around the ball. Inspect all of these parts for any damage and replace them if necessary.
Remove Mineral Deposits
Mineral deposits can accumulate on the ball, seat washer, and in the faucet body over time. Use a brush and white vinegar to remove any mineral deposits that may have built up. Removing mineral deposits is one of the incredible uses for white vinegar as it helps to soak the deposits. If the ball is cracked or chipped, replace it with a new one.
Install a New Seat and Spring
Once the ball, seat washer, and faucet body are clean and free of mineral deposits, you can install a new seat and spring. Start by inserting the seat into the faucet body. Make sure it is seated correctly, and then screw on the retaining nut. Tighten the nut with a wrench until it is snug.
Reinstall the Stem
Apply a small amount of plumber's grease to the o ring at the base of the valve stem. If possible, you can also replace the o ring, which is sometimes included in the repair kit, or the entire stem. Fit the stem into its housing, aligning the tabs on the stem with the slots in the housing.
Push the stem all the way down until it stops. Reinstall the bonnet nut and tighten it carefully with pliers or an adjustable wrench. It should be snug but don't over-tighten, or you may damage the faucet.
Check the Leaking and Reinstall the Handle
Turn on the water at the shut off valves and check for leaks around the base of the faucet. If necessary, use a wrench to tighten the packing nut slightly until the leak stops.
Replace the handle, making sure that it is in the correct position according to the manufacturer's instructions. Some handles have an indicator line or arrow that must be aligned with the stem. Others are keyed so that they can only be installed in one position.
Turn on the water and check for leaks again. If necessary, repeat the previous steps until the leak stops.
Test Your New Faucet
Run your new faucet for a few minutes to make sure that it is working properly. Check for any leaks and make sure that the water pressure is adequate. If everything seems to be working properly, you have successfully installed your new delta kitchen faucet. Note that delta is one of the best kitchen faucets with sprayers, so it will be able to serve you for a long without a fix.
FAQs on How to Fix a Leaking Delta Kitchen Faucet
How to find a repair kit for delta kitchen faucets?
If you need a repair kit for your delta kitchen faucet, you can find one at most hardware stores or online retailers.
How to fix a leak delta kitchen faucets?
You can fix a leak in your delta kitchen faucet by replacing the O-ring seals. These can be found in most repair kits. If the entire delta kitchen faucet is faulty, then you’ll need to replace your delta kitchen faucet if you have the knowledge and tools.
What is the best way to clean delta kitchen faucets?
To clean your delta kitchen faucet, simply use mild soap and warm water. You can also use a soft cloth to wipe down the faucet. Avoid using harsh chemicals or abrasive cleaners, as these can damage the finish.
Final Thought on How to Fix a Leaking Delta Kitchen Faucets
Kitchen faucets are very important fixtures, so it's essential to know how to fix a delta kitchen faucet if it starts to leak. By replacing the O-ring seals, you can easily repair most leaks. If your faucet is still leaking, you may need to replace the entire unit.