Installing the delta kitchen sink faucet is an important aspect of any kitchen remodel or update. Not only do they provide function, but they can also be quite stylish.
However, installing a Delta kitchen faucet can be difficult, especially if you're not familiar with the process. Not only is it frustrating to try and install a kitchen sink faucet on your own, but it can also be quite dangerous if you don't know what you're doing. You could easily damage your sink or plumbing fixtures if you're not careful. Learn more about kitchen faucet sprayer repair and solutions to other facet related problems here!
This is easy to follow installation guide will take you through the process of installing your new delta kitchen faucet.
Tools and Materials Needed
- Adjustable wrench
- Allen wrench
- New Delta kitchen faucet kit
- Silicon caulk [optional]
Instructions on How to Install a Delta Kitchen Faucet
Disconnect the Existing Faucet
Before you begin, it's important to disconnect the power supply to your kitchen sink. This will ensure that you don't accidentally electrocute yourself while working on the sink. Once the power is disconnected, begin by shutting off the water supply, then use an adjustable wrench to remove the existing faucet.
Install the Spout
With the old Delta kitchen faucet removed, it's time to begin installing the new one. Start by attaching the spout to the sink, then attach the handles. Thread the mounting screws into the mounting nut making sure they're only a few threads in.
Put the foam gasket on the spout and push the spout through the desired hole in the sink. From the bottom, screw the mounting nut and metal washer hand tight all the way up to the underside of the sink. When you have hand tightened the mounting nut as much as possible, use a screwdriver to tighten the screws a little more to ensure a snug fit. You don't want the spout to be able to wiggle around.
Install the Valve Stem
Now it's time to install the valve stem. Slip the foam gasket up around the tubes. Position it in the groove at the base of the valve. Push the tubes through the sink's hole while holding the gasket in place. Center the valve by aligning the lower tube with the mounting bracket.
As you tighten, make sure that the valve stays straight, facing the direction it needs to because sometimes it can move a little when tightening.
Install a Sprayer Hose
If you're installing a sink with a sprayer, especially a pull down kitchen faucet, the process is pretty similar to the one above.
Once you know how to replace Delta kitchen faucet sprayer hose, then you’ll be good to g. First, install the sprayer head onto the threaded end of the hose and hand tighten only. Attach the hose guide onto the other end of the hose and feed it through the underside of the sink. Remove the hose guide and feed the weight onto the hose.
Connect the sprayer hose to the valve hose by pushing them together. Secure them by installing the clip to hold them in place. Pull the sprayer hose out and check that when you do, the sprayer hose does not catch on anything under the sink. If the hose gets tangled up during the installation, it can make it difficult to use the sprayer.
Connect the Water Lines
Shut off the water at the shut-off valves beneath the sink. If there are no shut-off valves, shut off the water at the main valve to the house. Place a bucket beneath the P-trap to catch any water that may spill out when you disconnect the lines.
Use an adjustable wrench to loosen the compression nuts on the water lines. Be careful not to over-tighten or strip the threads.
Install the Faucet Trim
Install the decorative escutcheon plate over the hole in the sink. Attach the faucet trim to the escutcheon plate using the screws that come with the trim kit. Make sure that all o-rings and gaskets are in place before you screw on the trim. Connect the handles to the faucet using the screws that come with the handles.
Also, determine whether or not to use a gasket. This will depend on the type of counter or sink you have. If you have three holes faucet but wish to install a single hole faucet, then you must use a gasket. If your counter or sink has only one predrilled hole, you can install the faucet directly on top of it without using a gasket.
The gasket is provided by the majority of Delta products. However, not all do, and you may be required to purchase it individually. Make sure you cover all the mounting holes with a gasket. If you're installing the faucet through a single mounting hole, then omit the gasket and place the faucet.
Check for Leaks
Now that your faucet is installed, it's time to check for leaks. Begin by turning on the water at the shutoff valves, and then turn on each handle of your faucet. Move each handle back and forth to make sure they're working properly. Finally, turn off each handle and check under the sink for any drips. If there are any, tighten the connection until the leak stops.
Before using the faucet, flush out the sprayer hose. Pull out the sprayer head and unscrew it from the sprayer hose, ensuring to hold onto the sprayer hose. Run some water through the hose to clear out any debris that may be clogging it. Then screw the aerator back on and reattach the sprayer head.
Check for leaks several hours after the installation and once again the next day. Even a very small water leak under the sink can lead to mold and cabinet damage over time.
FAQs on How to Install Your Delta Kitchen Faucet
How do you choose Delta kitchen faucets?
Just like choosing other kitchen faucets, there are some factors you need to consider when choosing the best Delta kitchen faucet. These include the price, warranty, the size and shape, and the features you’re looking into.
How to remove Delta kitchen faucets?
To remove your Delta kitchen faucet, start by shutting off the water supply to the faucet. Next, use a wrench to loosen the screws that secure the faucet to the sink. With the screws removed, you should be able to lift the faucet off of the sink. If you have a sprayer attached to your faucet, you will need to disconnect the hose from the sprayer before you can remove the faucet.
Is plumber paste required when installing Delta kitchen faucets?
No, a plumber's paste is not required when installing Delta kitchen faucets. However, many people find it helpful to use a plumber's paste to ensure a tight seal between the faucet and the sink.
Why install a delta kitchen faucet?
Installing Delta kitchen is a good investment for your kitchen because it will last longer than any other faucet product. If you’re also looking for the best kitchen faucet with a sprayer, then delta is a good option.
Final Thought on How to Install Your Delta Kitchen Faucet
Installing a Delta kitchen faucet is a relatively easy process. However, if you are not comfortable performing the installation yourself, you can always hire a professional to do it for you.
Be sure to read all of the instructions that come with your Delta kitchen faucet before beginning the installation process. This will help you to avoid making any mistakes that could cause damage to your sink or faucet.