How To Fix Leaky Gerber Kitchen Faucets
Is water leaking from your Gerber handle kitchen faucet? Water leakage is a common problem with these faucets, but it's easy to fix. In this blog post, we'll show you how to properly fix a leaking Gerber handle kitchen faucet. We'll also provide some tips on how to prevent future leaks.
So, if you're dealing with a leaky Gerber handle kitchen faucet, read on for the solutions you need! Scroll down to know more about how to fix your Gerber handle kitchen faucet. Plus we will also answer some of the most commonly asked questions about fixing a Gerber handle kitchen faucet.
So let’s start!
Tools and Materials Needed to Fix Leaking Gerber Faucet:
- Adjustable pliers
- Allen wrench
- Flat head screwdriver
- Rubber gloves
- Gerber replacement cartridge (can be found online or at a hardware store)
- White vinegar
- Replacement springs and gaskets
Instructions on How to Repair a Leaky Gerber Kitchen Faucet
Video: Kitchen Faucet Leaks at the Base. Easy 5 min Fix.
Shut Off the Water Supply
Before you do anything, you'll need to shut off the water supply to your Gerber kitchen faucet. Locate the shut-off valves beneath the sink and turn them clockwise to close them.
Remove the Gerber Faucet Handle
Once the water is shut off, you can remove the handle of your Gerber kitchen faucet. Use an Allen wrench to remove the set screw that holds the handle in place. Once the set screw is removed, you should be able to pull the handle off. Lift the handle up straight to remove it from the faucet stem.
Remove the Bonnet or Hex Nut
With the handle of your Gerber faucet removed, you should be able to see a bonnet or hex nut. Use an adjustable wrench to remove this piece. If the bonnet is stuck, you may need to use a pair of pliers to get it started.
Remove the Collar of Gerber Faucet
Under the bonnet, you will find a collar. This piece is threaded and can be removed by hand. Put on a rubber glove to increase traction, grip the collar on the top of the Gerber faucet body and turn it counterclockwise. You may need to channel lock pliers to keep things moving.
Remove the Stem of Gerber Faucet
Once the collar is removed, you should be able to pull the stem out of the Gerber faucet. If it is stuck, you may need to use a pair of pliers. Remove the stem by pulling it straight up and out of its housing. Use pliers, if necessary, gripping the spindle at the top of the stem.
Remove the Ball, Gaskets, and Springs
The next step is to remove the ball, gaskets, and springs. The ball is located under the stem of your Gerber kitchen faucet and is held in place by a screw-on cap. Unscrew the cap with a Phillips head screwdriver and pull out the ball. Remove the gaskets and springs from around the ball. Inspect all of these parts for any damage and replace them if necessary.
Remove Mineral Deposits
Mineral deposits can accumulate on the ball, seat washer, and in the Gerber faucet body over time. Use a brush and white vinegar to remove any mineral deposits that may have built up. Removing mineral deposits is one of the incredible uses for white vinegar as it helps to soak the deposits. If the ball is cracked or chipped, replace it with a new one.
Install a New Seat and Spring
Once the ball, seat washer, and faucet body are clean and free of mineral deposits, you can install a new seat and spring. Start by inserting the seat into the Gerber faucet body. Make sure it is seated correctly, and then screw on the retaining nut. Tighten the nut with a wrench until it is snug.
Reinstall the Stem of Gerber Faucet
Apply a small amount of plumber's grease to the o ring at the base of the valve stem. If possible, you can also replace the o ring, which is sometimes included in the Gerber repair kit, or the entire stem. Fit the stem into its housing, aligning the tabs on the stem with the slots in the housing.
Push the stem all the way down until it stops. Reinstall the bonnet nut and tighten it carefully with pliers or an adjustable wrench. It should be snug but don't over-tighten, or you may damage the Gerber faucet.
Check the Leaking and Reinstall the Handle
Turn on the water at the shut-off valves and check for leaks around the base of the Gerber faucet. If necessary, use a wrench to tighten the packing nut slightly until the leak stops.
Replace the handle, making sure that it is in the correct position according to Gerber's instructions. Some handles have an indicator line or arrow that must be aligned with the stem. Others are keyed so that they can only be installed in one position.
Turn on the water and check for leaks again. If necessary, repeat the previous steps until the leak stops.
Test Your Newly Installed Gerber Faucet
Run your newly installed Gerber faucet for a few minutes to make sure that it is working properly. Check for any leaks and make sure that the water pressure is adequate. If everything seems to be working properly, you have successfully installed your new Gerber kitchen faucet. Note that Gerber is one of the best kitchen faucets with sprayers, so it will be able to serve you for a long time without a fix.
FAQs on Fixing a Leaky Gerber Kitchen Faucet
What are the most common causes of leaky Gerber kitchen faucets?
There can be several reasons for a leaky Gerber kitchen faucet, but the most common cause is a worn-out washer. Over time, the washer will become misshapen and no longer provide a tight seal. This can allow water to seep through, resulting in a drip or steady stream of water.
What is the best way to clean Gerber kitchen faucets?
To clean your Gerber kitchen faucet, simply use mild soap and warm water. You can also use a soft cloth to wipe down the faucet. Avoid using harsh chemicals or abrasive cleaners, as these can damage the finish.
How to fix a leak in Gerber kitchen faucets?
You can fix a leak in your Gerber kitchen faucet by replacing the O-ring seals. These can be found in most repair kits. If the entire Gerber kitchen faucet is faulty, then you’ll need to replace your Gerber kitchen faucet if you have the knowledge and tools.
How to find a repair kit for Gerber kitchen faucets?
If you need a repair kit for your Gerber kitchen faucet, you can find one at most hardware stores or online retailers.
How to spot the model number on a Gerber kitchen faucet?
The faucet comes with a tag that displays the model number along the cold water supply line of the faucet. The model number usually starts with P/N and usually follows this pattern… 6348-T4-AB
Final Thought on How to Fix a Leaking Gerber Kitchen Faucets
Kitchen faucets are very important fixtures, so it's essential to know how to fix a Gerber kitchen faucet if it starts to leak. By replacing the O-ring seals, you can easily repair most leaks. If your Gerber faucet is still leaking, you may need to replace the entire unit.
If you are looking for a guide on fixing a faucet from a brand other than Gerber, see our brand chart below.
Fixing Leaky Kitchen Faucet by Brand
- Kohler Leaky Faucet Repair
- Akicon Leaky Faucet Repair
- Hansgrohe Leaky Faucet Repair
- Kingston Brass Leaky Faucet Repair
- T&S Brass Leaky Faucet Repair
- WestBrass Leaky Faucet Repair
- Karran Leaky Faucet Repair
- Rohl Leaky Faucet Repair
- American Standard Leaky Faucet Repair
- Gerber Leaky Faucet Repair
- Dishmaster Leaky Faucet Repair
- Zurn Leaky Faucet Repair
- Transolid Leaky Faucet Repair
- Delta Leaky Faucet Repair
- Pfister Leaky Faucet Repair
- Moen Leaky Faucet Repair
- Kraus Leaky Faucet Repair
- Nuvo Leaky Faucet Repair
- Newport Brass Leaky Faucet Repair
- Grohe Leaky Faucet Repair
- AXOR Leaky Faucet Repair
- Signature Hardware Leaky Faucet Repair
- Houzer Leaky Faucet Repair
- Waterstone Leaky Faucet Repair
- Vigo Leaky Faucet Repair
- Peerless Leaky Faucet Repair
Download Free Chart Now!
Your email will be used only to confirm your request and to provide free kitchen information. By submitting your info on this form, you are agreeing to be contacted regarding your service request by means of email. This is no obligation form and doesn’t require you to purchase any service.