There are few things more frustrating than a leaky faucet, especially if you're trying to cook and clean at the same time! Luckily it's possible for everyone to fix a leaking Rohl handle kitchen faucet without the help of a plumber.
But if you have a leaking Kraus handle from time to time- don't worry because fixing this problem can be easy as pie ( kitchen faucets drips are usually located near water sources). In our blog post today we will show how by following some simple steps; everything should get back on track for good measure.
So let’s begin fixing your leaking kitchen faucet!
Tools and Materials Needed to Fix Leaking Rohl Faucet:
- Adjustable pliers
- Allen wrench
- Flat head screwdriver
- Rubber gloves
- Rohl replacement cartridge (can be found online or at a hardware store)
- White vinegar
- Replacement springs and gaskets
Instructions on How to Repair a Leaky Rohl Kitchen Faucet
Video: How to Fix a Leaky Faucet | The Home Depot.
Shut Off the Water Supply
Before you do anything, you'll need to shut off the water supply to your Rohl kitchen faucet. Locate the shut-off valves beneath the sink and turn them clockwise to close them.
Remove the Rohl Faucet Handle
Once the water is shut off, you can remove the handle of your Rohl kitchen faucet. Use an Allen wrench to remove the set screw that holds the handle in place. Once the set screw is removed, you should be able to pull the handle off. Lift the handle up straight to remove it from the faucet stem.
Remove the Bonnet or Hex Nut
With the handle of your Rohl faucet removed, you should be able to see a bonnet or hex nut. Use an adjustable wrench to remove this piece. If the bonnet is stuck, you may need to use a pair of pliers to get it started.
Remove the Collar of Rohl Faucet
Under the bonnet, you will find a collar. This piece is threaded and can be removed by hand. Put on a rubber glove to increase traction, grip the collar on the top of the Rohl faucet body and turn it counterclockwise. You may need to channel lock pliers to keep things moving.
Remove the Stem
Once the collar is removed, you should be able to pull the stem out of the Rohl faucet. If it is stuck, you may need to use a pair of pliers. Remove the stem by pulling it straight up and out of its housing. Use pliers, if necessary, gripping the spindle at the top of the stem.
Remove the Ball, Gaskets, and Springs
The next step is to remove the ball, gaskets, and springs. The ball is located under the stem of your Rohl kitchen faucet and is held in place by a screw-on cap. Unscrew the cap with a Phillips head screwdriver and pull out the ball. Remove the gaskets and springs from around the ball. Inspect all of these parts for any damage and replace them if necessary.
Remove Mineral Deposits from Rohl Kitchen Faucet
Mineral deposits can accumulate on the ball, seat washer, and in the Rohl faucet body over time. Use a brush and white vinegar to remove any mineral deposits that may have built up. Removing mineral deposits is one of the incredible uses for white vinegar as it helps to soak the deposits. If the ball is cracked or chipped, replace it with a new one.
Install a New Seat and Spring
Once the ball, seat washer, and faucet body are clean and free of mineral deposits, you can install a new seat and spring. Start by inserting the seat into the Rohl faucet body. Make sure it is seated correctly, and then screw on the retaining nut. Tighten the nut with a wrench until it is snug.
Reinstall the Stem of Rohl Faucet
Apply a small amount of plumber's grease to the o ring at the base of the valve stem. If possible, you can also replace the o ring, which is sometimes included in the Rohl repair kit, or the entire stem. Fit the stem into its housing, aligning the tabs on the stem with the slots in the housing.
Push the stem all the way down until it stops. Reinstall the bonnet nut and tighten it carefully with pliers or an adjustable wrench. It should be snug but don't over-tighten, or you may damage the Rohl faucet.
Check the Leaking and Reinstall the Handle
Turn on the water at the shut-off valves and check for leaks around the base of the Rohl faucet. If necessary, use a wrench to tighten the packing nut slightly until the leak stops.
Replace the handle, making sure that it is in the correct position according to Rohl's instructions. Some handles have an indicator line or arrow that must be aligned with the stem. Others are keyed so that they can only be installed in one position.
Turn on the water and check for leaks again. If necessary, repeat the previous steps until the leak stops.
Test Your Newly Installed Rohl Faucet
Run your newly installed Rohl faucet for a few minutes to make sure that it is working properly. Check for any leaks and make sure that the water pressure is adequate. If everything seems to be working properly, you have successfully installed your new Rohl kitchen faucet. Note that Rohl is one of the best kitchen faucets with sprayers, so it will be able to serve you for a long time without a fix.
FAQs on Fixing a Leaky Rohl Kitchen Faucet
What are the most common causes of leaky Rohl kitchen faucets?
There can be several reasons for a leaky Rohl kitchen faucet, but the most common cause is a worn-out washer. Over time, the washer will become misshapen and no longer provide a tight seal. This can allow water to seep through, resulting in a drip or steady stream of water.
How to find a repair kit for Rohl kitchen faucets?
If you need a repair kit for your Rohl kitchen faucet, you can find one at most hardware stores or online retailers.
How to spot the model number on a Rohl kitchen faucet?
The faucet comes with a tag that displays the model number along the cold water supply line of the faucet. The model number usually starts with P/N and usually follows this pattern… 6348-T4-AB
How to fix a leak in Rohl kitchen faucets?
You can fix a leak in your Rohl kitchen faucet by replacing the O-ring seals. These can be found in most repair kits. If the entire Rohl kitchen faucet is faulty, then you’ll need to replace your Rohl kitchen faucet if you have the knowledge and tools.
What is the best way to clean Rohl kitchen faucets?
To clean your Rohl kitchen faucet, simply use mild soap and warm water. You can also use a soft cloth to wipe down the faucet. Avoid using harsh chemicals or abrasive cleaners, as these can damage the finish.
Final Thought on How to Fix a Leaking Rohl Kitchen Faucets
Kitchen faucets are very important fixtures, so it's essential to know how to fix a Rohl kitchen faucet if it starts to leak. By replacing the O-ring seals, you can easily repair most leaks. If your Rohl faucet is still leaking, you may need to replace the entire unit.
Check out our chart below, which contains guides for leaking faucets other than Rohl.
Fixing Leaky Kitchen Faucet by Brand
- Kohler Leaky Faucet Repair
- Akicon Leaky Faucet Repair
- Hansgrohe Leaky Faucet Repair
- Kingston Brass Leaky Faucet Repair
- T&S Brass Leaky Faucet Repair
- WestBrass Leaky Faucet Repair
- Karran Leaky Faucet Repair
- Rohl Leaky Faucet Repair
- American Standard Leaky Faucet Repair
- Gerber Leaky Faucet Repair
- Dishmaster Leaky Faucet Repair
- Zurn Leaky Faucet Repair
- Transolid Leaky Faucet Repair
- Delta Leaky Faucet Repair
- Pfister Leaky Faucet Repair
- Moen Leaky Faucet Repair
- Kraus Leaky Faucet Repair
- Nuvo Leaky Faucet Repair
- Newport Brass Leaky Faucet Repair
- Grohe Leaky Faucet Repair
- AXOR Leaky Faucet Repair
- Signature Hardware Leaky Faucet Repair
- Houzer Leaky Faucet Repair
- Waterstone Leaky Faucet Repair
- Vigo Leaky Faucet Repair
- Peerless Leaky Faucet Repair
Download Free Chart Now!
Your email will be used only to confirm your request and to provide free kitchen information. By submitting your info on this form, you are agreeing to be contacted regarding your service request by means of email. This is no obligation form and doesn’t require you to purchase any service.