Have you ever gone to turn on your kitchen sink faucet, only to be greeted by an annoying dripping sound? If you have, then you know how frustrating it can be to have a leaking faucet. What's even worse is when you can't figure out how to fix it! 

But don't worry, we're here to help. In this blog post, we'll show you how to fix a leaky American Standard handle kitchen faucet.  Keep reading to find out how you can fix a leaking Signature Hardware handle kitchen faucet without any fuss. 

We will also answer a few FAQs in the end, so keep reading!

Signature Hardware Kitchen Sink Faucet
Credits: www.signaturehardware.com

Tools and Materials Needed to Fix Leaking Signature Hardware Faucet:

  • Adjustable pliers
  • Allen wrench
  • Flat head screwdriver
  • Rubber gloves
  • Signature Hardware replacement cartridge (can be found online or at a hardware store)
  • White vinegar
  • Replacement springs and gaskets

Instructions on How to Repair a Leaky Signature Hardware Kitchen Faucet

Video: How to Fix a Leaky Faucet | The Home Depot

Shut Off the Water Supply

Before you do anything, you'll need to shut off the water supply to your Signature Hardware kitchen faucet. Locate the shut-off valves beneath the sink and turn them clockwise to close them.

Remove the Signature Hardware Faucet Handle

Once the water is shut off, you can remove the handle of your Signature Hardware kitchen faucet. Use an Allen wrench to remove the set screw that holds the handle in place. Once the set screw is removed, you should be able to pull the handle off. Lift the handle up straight to remove it from the faucet stem.

Remove the Bonnet or Hex Nut

With the handle of your Signature Hardware faucet removed, you should be able to see a bonnet or hex nut. Use an adjustable wrench to remove this piece. If the bonnet is stuck, you may need to use a pair of pliers to get it started.

Remove the Collar of Signature Hardware Faucet

Under the bonnet, you will find a collar. This piece is threaded and can be removed by hand. Put on a rubber glove to increase traction, grip the collar on the top of the Signature Hardware faucet body and turn it counterclockwise. You may need to channel lock pliers to keep things moving.

Remove the Stem

Once the collar is removed, you should be able to pull the stem out of the Signature Hardware faucet. If it is stuck, you may need to use a pair of pliers. Remove the stem by pulling it straight up and out of its housing. Use pliers, if necessary, gripping the spindle at the top of the stem.

Remove the Ball, Gaskets, and Springs

The next step is to remove the ball, gaskets, and springs. The ball is located under the stem of your Signature Hardware kitchen faucet and is held in place by a screw-on cap. Unscrew the cap with a Phillips head screwdriver and pull out the ball. Remove the gaskets and springs from around the ball. Inspect all of these parts for any damage and replace them if necessary.

Remove Mineral Deposits from Signature Hardware Faucet

Mineral deposits can accumulate on the ball, seat washer, and in the Signature Hardware faucet body over time. Use a brush and white vinegar to remove any mineral deposits that may have built up. Removing mineral deposits is one of the incredible uses for white vinegar as it helps to soak the deposits. If the ball is cracked or chipped, replace it with a new one.

Install a New Seat and Spring

Once the ball, seat washer, and faucet body are clean and free of mineral deposits, you can install a new seat and spring. Start by inserting the seat into the Signature Hardware faucet body. Make sure it is seated correctly, and then screw on the retaining nut. Tighten the nut with a wrench until it is snug.

Reinstall the Stem of your Signature Hardware Faucet

Apply a small amount of plumber's grease to the o ring at the base of the valve stem. If possible, you can also replace the o ring, which is sometimes included in the Signature Hardware repair kit, or the entire stem. Fit the stem into its housing, aligning the tabs on the stem with the slots in the housing.

Push the stem all the way down until it stops. Reinstall the bonnet nut and tighten it carefully with pliers or an adjustable wrench. It should be snug but don't over-tighten, or you may damage the Signature Hardware faucet. For more information on how to tighten a kitchen faucet, read the article on site.

signature hardware sink faucet installation and maintenance
Picture Credits: www.signaturehardware.com

Check the Leaking and Reinstall the Handle

Turn on the water at the shut-off valves and check for leaks around the base of the Signature Hardware faucet. If necessary, use a wrench to tighten the packing nut slightly until the leak stops.

Replace the handle, making sure that it is in the correct position according to Signature Hardware's instructions. Some handles have an indicator line or arrow that must be aligned with the stem. Others are keyed so that they can only be installed in one position.

Turn on the water and check for leaks again. If necessary, repeat the previous steps until the leak stops.

Test Your Newly Installed Signature Hardware Faucet

Run your newly installed Signature Hardware faucet for a few minutes to make sure that it is working properly. Check for any leaks and make sure that the water pressure is adequate. If everything seems to be working properly, you have successfully installed your new Signature Hardware kitchen faucet. Note that Signature Hardware is one of the best kitchen faucets with sprayers, so it will be able to serve you for a long time without a fix.

FAQs on Fixing a Leaky Signature Hardware Kitchen Faucet

What is the best way to clean Signature Hardware kitchen faucets?

To clean your Signature Hardware kitchen faucet, simply use mild soap and warm water. You can also use a soft cloth to wipe down the faucet. Avoid using harsh chemicals or abrasive cleaners, as these can damage the finish.

How to spot the model number on a Signature Hardware kitchen faucet?

The faucet comes with a tag that displays the model number along the cold water supply line of the faucet. The model number usually starts with P/N and usually follows this pattern… 6348-T4-AB

How to find a repair kit for Signature Hardware kitchen faucets?

If you need a repair kit for your Signature Hardware kitchen faucet, you can find one at most hardware stores or online retailers.

What are the most common causes of leaky Signature Hardware kitchen faucets?

There can be several reasons for a leaky Signature Hardware kitchen faucet, but the most common cause is a worn-out washer. Over time, the washer will become misshapen and no longer provide a tight seal. This can allow water to seep through, resulting in a drip or steady stream of water. 

How to fix a leak in Signature Hardware kitchen faucets?

You can fix a leak in your Signature Hardware kitchen faucet by replacing the O-ring seals. These can be found in most repair kits. If the entire Signature Hardware kitchen faucet is faulty, then you’ll need to replace your Signature Hardware kitchen faucet if you have the knowledge and tools.

Final Thought on How to Fix a Leaking Signature Hardware Kitchen Faucets

Kitchen faucets are very important fixtures, so it's essential to know how to fix a Signature Hardware kitchen faucet if it starts to leak. By replacing the O-ring seals, you can easily repair most leaks. If your Signature Hardware faucet is still leaking, you may need to replace the entire unit.

For fixing leaky faucets of brands other than Signature Hardware, see our chart below.

Download Free Chart Now!

Your email will be used only to confirm your request and to provide free kitchen information. By submitting your info on this form, you are agreeing to be contacted regarding your service request by means of email. This is no obligation form and doesn’t require you to purchase any service.

norton_black
comodo_black